Top Industrial Belt Conveyor Issues
The advent of troughed belt conveyors fundamentally changed industrial processing, increasing efficiencies, reducing labor requirements, improving safety, and streamlining production. These flexible devices have become the standard for moving product and material around a facility and are found in every industry imaginable.
While belt conveyors provide a reliable, efficient bulk handling solution, they can experience occasional problems. And when issues arise, they can wreak havoc on a production line. Below are some of the most commonly seen issues when working with belt conveyors, including what causes these problems and how to prevent them.
Note: This is not a comprehensive list and does not substitute for the expertise of a professional. Always consult your original equipment manufacturer or manual to ensure all necessary safety, maintenance, and troubleshooting guidelines are followed. Maintenance and storage procedures should always be carried out by a trained professional. FEECO does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this guide and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage.
Carryback is the material that remains on the belt after discharge and is perhaps the most common struggle among conveyor pulley. Typically all conveyors experience carryback to some extent, but given its potential for serious consequences, keeping it to a minimum is essential.
WHY CARRYBACK IS AN ISSUE
Carryback creates a messy and potentially hazardous work environment, as it gets into the undercarriage and surrounding area of the conveyor. This can cause outages and increase the time devoted to cleaning and maintenance.
Not only does carryback create a mess, but material allowed to build up on rollers, idlers, and pulleys degrades these components, causing excessive wear. Further, a buildup of carryback can also cause belt tracking issues, potentially wearing and damaging the belt.
WHAT CAUSES CARRYBACK
Carryback is largely a result of the conveyed material’s characteristics and propensity for sticking. In general, a material with a higher moisture content is more likely to stick to the belt. Similarly, carryback can be more of a problem in humid environments where hygroscopic materials pull moisture from the air, increasing the likelihood of sticking.
Sticking can also occur when condensation is produced as a result of extreme temperature differences between the material and the belt.
HOW TO PREVENT CARRYBACK
The best way to prevent carryback is to utilize one or more belt cleaners. Belt cleaners can be installed at both the head and tail pulley and serve to ride against the conveyor belt, dislodging any material that may be adhered to the belt. These devices substantially reduce buildup on the belt, and depending on the level of carryback, several options may be appropriate. Common options include a self-cleaning tail pulley, return side belt plow (v-plow), and dual belt cleaners.
Routine cleaning should also be prioritized as part of a conveyor head pulley maintenance program in order to minimize any remaining buildup on components.
CONVEYOR BELT MISTRACKING
Tracking, or training, refers to the way in which the belt rides on the rollers. Conveyor belts should always track centrally. Mistracking occurs when the conveyor rubber belt rides unevenly on rollers, favoring one side over the other.
Like carryback, mistracking can cause several issues in a conveyor system. This includes uneven belt wear, belt damage resulting from catching or rubbing on surrounding infrastructure, material spillage, warped belting or belts that are not square, and more.
The advent of troughed belt conveyors fundamentally changed industrial processing, increasing efficiencies, reducing labor requirements, improving safety, and streamlining production. These flexible devices have become the standard for moving product and material around a facility and are found in every industry imaginable.
While belt conveyors provide a reliable, efficient bulk handling solution, they can experience occasional problems. And when issues arise, they can wreak havoc on a production line. Below are some of the most commonly seen issues when working with belt conveyors, including what causes these problems and how to prevent them.
Note: This is not a comprehensive list and does not substitute for the expertise of a professional. Always consult your original equipment manufacturer or manual to ensure all necessary safety, maintenance, and troubleshooting guidelines are followed. Maintenance and storage procedures should always be carried out by a trained professional. FEECO does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this guide and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage.
Carryback is the material that remains on the belt after discharge and is perhaps the most common struggle among conveyor pulley. Typically all conveyors experience carryback to some extent, but given its potential for serious consequences, keeping it to a minimum is essential.
WHY CARRYBACK IS AN ISSUE
Carryback creates a messy and potentially hazardous work environment, as it gets into the undercarriage and surrounding area of the conveyor. This can cause outages and increase the time devoted to cleaning and maintenance.
Not only does carryback create a mess, but material allowed to build up on rollers, idlers, and pulleys degrades these components, causing excessive wear. Further, a buildup of carryback can also cause belt tracking issues, potentially wearing and damaging the belt.
WHAT CAUSES CARRYBACK
Carryback is largely a result of the conveyed material’s characteristics and propensity for sticking. In general, a material with a higher moisture content is more likely to stick to the belt. Similarly, carryback can be more of a problem in humid environments where hygroscopic materials pull moisture from the air, increasing the likelihood of sticking.
Sticking can also occur when condensation is produced as a result of extreme temperature differences between the material and the belt.
HOW TO PREVENT CARRYBACK
The best way to prevent carryback is to utilize one or more belt cleaners. Belt cleaners can be installed at both the head and tail pulley and serve to ride against the conveyor belt, dislodging any material that may be adhered to the belt. These devices substantially reduce buildup on the belt, and depending on the level of carryback, several options may be appropriate. Common options include a self-cleaning tail pulley, return side belt plow (v-plow), and dual belt cleaners.
Routine cleaning should also be prioritized as part of a conveyor head pulley maintenance program in order to minimize any remaining buildup on components.
CONVEYOR BELT MISTRACKING
Tracking, or training, refers to the way in which the belt rides on the rollers. Conveyor belts should always track centrally. Mistracking occurs when the conveyor rubber belt rides unevenly on rollers, favoring one side over the other.
Like carryback, mistracking can cause several issues in a conveyor system. This includes uneven belt wear, belt damage resulting from catching or rubbing on surrounding infrastructure, material spillage, warped belting or belts that are not square, and more.